The Edge40 replacement cell is only compatible with CircuPool’s Edge Control module. The Edge40 salt cell is the factory original replacement cell model designed to easily drop in place and allow you to replace your old Edge40 cell in minutes. This cell is made to meet or exceed original factory specs and has 100% guaranteed compatibility.
Featuring a clear inline housing and built-in titanium electrode plates, the CircuPool EDGE Series electrolytic cell is designed to last longer and fit all EDGE-Series systems. With threaded connections on both ends of the cell housing, it’s easy to access or remove the cell of cleaning, maintenance, or seasonal changes.
Replacing the Edge40 cell will allow your salt chlorine generator to begin chlorinating again if your old Edge40 salt cell has been depleted. The Edge40 cell sanitizes your swimming pool in an eco-friendly and cost-efficient way, and also helps provide a luxurious swimming experience without the eye irritation and dry skin.
Sizing:
When replacing your Edge40 salt cell, take this opportunity to make sure it is sized correctly. Sizing your salt cell properly is key to making sure you will not need to supplement with additional chlorine or shock your pool, and also extends the lifespan of your cell. The industry recommends using a salt cell with a max capacity of 1.5-2 times the actual size of your pool (more is better). The Edge40 is manufacturer rated for a maximum capacity of 40,000 gallons.
Compatibility:
This replacement salt cell for the Edge40 is 100% compatible with original systems (no software/firmware issues). The Edge40 cell has the same length, threading, and cable connection for direct replacement.
To get the most life out of your salt cell and to keep your pool running without unexpected interruptions, make sure it is sized correctly, maintain correct water balance, and be sure and inspect your cell at least every 3 months for leaks, debris, and calcium scale. Be sure to follow instructions in the product manual and clean the cell as often as the system indicates.
General FAQ
If your salt cell needs to be replaced, you probably have a problem with low chlorine, but if your chlorine level is a problem then the cell is only one of several possible issues, notably including excessive chlorine demand. Essentially, you have either a system problem or a water problem.
System problems will generally reveal themselves with error messages or warning lights on the control module. The typical indications of the cell needing replacement will be one or both of the following: Low Salt warnings that are present with correct salinity and Check/Clean Cell warnings that display when the cell is verifiably clean.
If you are referring to buying the same brand, there’s no question that the original OEM salt cell is exactly what your system was designed to use. However, commonly there are aftermarket replacement cells available which fit into place and operate quite satisfactorily. It is your prerogative to employ one of these aftermarket replacements if you are satisfied with the specifications, price warranty, and reported compatibility.
If you were asking about buying the same capacity cell, then OEM or aftermarket alike, you need to first determine whether your control or power module can accommodate a different size. Assuming you can change sizes, a larger cell is virtually always a good choice. However, in downsizing, make sure the smaller cell is still sufficiently large to maintain 1.5-2 times sizing of the cell relative to the pool’s volume.
There are no reviews yet
Questions From Customers
Q:
is the edge 25 or 40 a direct replacement for a t-15 hayward ? approx 15000 gallons , THX !
Asked by: dan
- 2/15/2022
1
1
|
Chlorine Output
|
1.7 lbs /day
|
|
Manufacturer Max Capacity
|
40,000 gallons
|
|
Manufacturer Warranty
|
7 Years
|
|
Warranty Penalty for Self-Install
|
No
|
|
Salinity Range:
|
2800-4500 ppm
|
|
Self-Cleaning:
|
Yes, Reverse Polarity
|
|
Clear Cell:
|
Yes
|
|
O-Ring included:
|
No
|
|
Unions Included:
|
No
|
|
Cell cord length:
|
8’
|
|
Cable Connection Type:
|
Quick Connect
|
|
Weight:
|
4 lbs
|
|
Weather / UV-Resistance:
|
Designed for Outdoor Installation and Operation
|
Featuring a clear inline housing and built-in titanium electrode plates, the CircuPool EDGE Series electrolytic cell is designed to last longer and fit all EDGE-Series systems. With threaded connections on both ends of the cell housing, it’s easy to access or remove the cell of cleaning, maintenance, or seasonal changes.
For easy install, simply attach the threaded connections to 2” unions, which are glued to the existing PVC return-line plumbing, or may already be present if you are simply replacing your old cell. Clear cell housing also makes it easy to watch the chlorine generation process or inspect the cell at work.
Manufacturer 7 Year Limited Warranty for residential use. Most manufacturer chlorine generator warranties are pro-rated. All warranties offered are provided by the relative manufacturer and are limited to the terms and proration they provide. See manufacturer's documentation for a full description of warranty terms and conditions.
